Lea Greaseless Compound, also known as Lea Satene, coats a polishing mop with a hard abrasive head. The result is a flexible abrasive wheel for satin finishing, brushed effects, deburring and light grinding, which can be re-headed whenever the abrasive wears.
This guide explains how to make and maintain a greaseless (Satene) mop: choosing the mop, applying Lea No.3 Glue where you need extra adhesion, building the compound head, and re-heading as you work.
Why Make a Greaseless Mop?
- Economical: a greaseless mop is a low-cost way to make an abrasive wheel, and is re-headed rather than replaced.
- Flexible: it has more give than a grinding wheel, without the disintegration of nylon-style abrasive mops.
- Adjustable: the mop you choose sets the flexibility, from rigid felt and stitched mops to very flexible loosefold mops.
- Clean: the greaseless formula leaves parts ready for lacquering or coating, with no degreasing.
Greaseless mops are popular in fabrication, sculpture, jewellery and general metal finishing.
What You Need
| Item | Notes |
|---|---|
| Lea Greaseless Compound | Choose the grade for the finish: A80 coarse to A320 extra fine. See the grade guide. |
| A polishing mop or felt wheel | The mop sets how rigid or flexible the finished head will be. |
| A mop dresser | For raking new mops before heading, and dressing glazed mops before re-heading. |
| Lea No.3 Glue | Optional: for stronger adhesion, rigid heads and parts with sharp edges. |
| A polishing spindle or bench polisher | You will switch the motor on and off while applying glue and compound. |
Choose the Right Mop
| Job | Mop |
|---|---|
| Flexible finishing and deburring | Soft stitched mops |
| Satin finishing and mopping | Loosefold mops, usually unstitched, such as Loosefold G or Loosefold WDR, or string wheels |
| Heavy polishing | Hard stitched mops such as White Stitched, or felt wheels, which can be pre-sized with No.3 Glue for better adhesion |
A felt wheel or stitched mop gives a more rigid head, though not as hard as a grinding wheel; a loosefold mop gives a very flexible one. Choose a mop diameter that gives a peripheral speed of 1,500 to 6,000 surface feet per minute, depending on the result you need.
How Lea Compound Goes On
Lea Greaseless Compound is abrasive grit held in a glue binder. When the bar is pressed against a turning mop, friction softens the end of the bar and it transfers onto the mop face, where it dries to a hard abrasive head.
The mop needs to be turning slowly while you apply it. At full speed, the softened compound is thrown off the mop before it can bond, and the head comes out patchy and cracked. Press hard on a slow mop instead, and the motor will stall. The answer is the start and stop method: switch the motor on, switch it off before it reaches full speed, and apply the bar as the mop coasts down.
Before You Start
- Prepare the mop. Rake a new mop with a mop dresser to open up the fibres, so the compound has something to grip.
- Use one mop per grade. Once a mop has been headed with a grade, keep it for that grade only.
- Prepare the bar. Cut and peel back about ½” of the plastic tube. Never remove the whole tube, which supports the bar as you use it.
Step 1: Apply No.3 Glue (Optional)
Use Lea No.3 Glue when parts have sharp edges, projections or recesses that would rake the compound head away early, or when you want a firmer, longer-lasting head.
- Start and stop: switch the motor on, then switch it off before the mop reaches full speed.
- Apply as it slows: as the mop coasts down, press the No.3 Glue bar against the mop face and move it across the full width. The glue softens and spreads onto the mop.
- Choose the coat: a light coat keeps the mop flexible; a heavier coat, built up with repeated bursts, gives a firmer base for a rigid head.
- Let it dry: give the mop short, gentle bursts of power so it turns slowly, until the glue is no longer sticky to the touch. This takes about two minutes.
Step 2: Head the Mop with Compound
- Start and stop: switch the motor on, then switch it off before the mop reaches full speed.
- Apply as it slows: as the mop coasts down, press the Lea Greaseless bar firmly against the face and move it across the full width. The bar slows the mop as the compound melts onto it.
- Repeat in short bursts until the whole face is evenly coloured with compound.
- Let the coat dry until it is hard and no longer tacky. Give the mop short, gentle bursts of power so it turns slowly while it dries.
- Build in thin coats: for a thicker, more rigid head, repeat the process, letting each coat dry before the next. Heads up to 3/16″ thick can be built over a heavy coat of No.3 Glue.
Before use:
Allow the head at least a few minutes to harden. A head left longer, ideally overnight, will last longer; for maximum head retention, Lea recommends oven drying. For extra cut, lightly crack the surface with a hammer to expose fresh abrasive edges.
Using and Re-Heading
- Run slower than grease bar polishing: approx. 5,000 sf/m for flexible polishing and 1,500–2,000 sf/m for brushed effects.
- Work in stages: go through two or three grades from coarse to fine, polishing at a different angle each time.
- Re-head before the head wears through: never let the compound wear down to the fibres of the mop. Re-head with the same start and stop method; a warm mop dries the new coat quickly.
- If new compound won’t stick, the face has glazed. Dress it lightly with a mop dresser, then re-head.
- Store bars carefully: re-cover any exposed bar and keep bars away from heat.
Troubleshooting
| Problem | Likely Cause | What to Do |
|---|---|---|
| Compound flies off the mop | Mop turning too fast | Apply as the mop coasts down, using the start and stop method |
| Motor stalls | Too much pressure on a slow mop | Use shorter bursts and lighter pressure until the mop is coated |
| Head is patchy or cracked | Coat too thick, or applied at speed | Build several thin coats, drying each one |
| Head wears away quickly | Coat not fully dry, or sharp edges raking it | Allow longer drying; use No.3 Glue first |
| New compound won’t stick | Glazed mop face | Dress the mop with a mop dresser, then re-head |
Need Help Choosing?
Contact Moleroda with the material being finished, its current surface condition, the mop or machine you are using and the finish you need.
Frequently Asked Questions (FAQs)
A polishing mop headed with Lea Greaseless (Satene) Compound, giving a flexible abrasive wheel for satin finishing, deburring and light grinding.
Not always. Use it for rigid heads, aggressive cutting, or parts with sharp edges and projections that cause a raking action and wear the head away early.
The mop is turning too fast. Switch the motor off before it reaches full speed and apply the bar as the mop coasts down.
A mop can be headed in under 10 minutes with the start and stop method, but allow the head at least a few minutes to harden before use. A longer drying time gives a longer-lasting head.
Heads up to 3/16″ thick can be built over a heavy coat of No.3 Glue, letting each coat dry before the next.
A loosefold mop, usually unstitched, or a string wheel. Use soft stitched mops for flexible finishing and deburring, and hard stitched mops or felt wheels for heavy polishing.
Apply fresh compound with the same start and stop method before the head wears down to the mop fibres. If the new compound won’t stick, dress the mop with a mop dresser first.

